Hi, We've got about 15 HP V-M200 APs in our school district, all were replacements for our older Netgear products. The problem is that they require almost daily power cycles to continue functioning. They function correctly for a day or two, and then suddenly stop forwarding traffic.

Click here to view the HP M200-802.11n Access Point Series Worldwide QuickSpecs in html format. Link for the drivers, firmware, software and manuals.

The SSID is still visible, and clients maintain their associations, but all network resources are inaccessible. A quick note, some of these access points are being powered by POE and others are not. The same problem exists regardless. Also, they all have different SSID's and all APs within the same building are operating on different channels. They obtain IP's through DHCP reservations tied to their wireless MAC addresses. The current firmware is 5.4.1.0-01-9867 which came preinstalled. Hp Laserjet 1015 Driver For Windows 10 64 Bit.

I am unable to find a new version. I can't help much except to say that I know what you're talking about. I got 10 of them last Christmas break to install at my medium-size independent school, and I had that same problem (still associated, but no network traffic) with some of them all the rest of the school year. That was on the original firmware (at least 2 versions prior to yours), and then over the summer I upgraded them to the latest then (and still current on the support page) 5.4.1.0-01-9503, and it seems to have made all the difference.

Nothing changed in my configuration otherwise or switch settings otherwise. I don't suppose you can install a firmware version lower than what your AP came with. All of a sudden I'd get a frantic call that a classroom of laptops had a strong network connection but no connectivity.

I could ping the AP without any problem, but the web interface was very slow, glacially slow to load. So that is how I got by, I created a single group of bookmarks that would all open in tabs with one click every morning, and then I could run down the tab line close the tabs of the APs which loaded right up.

If any were still spinning well after the others had loaded the home page, I would reboot them. This sucks, I know, but it minimized precious downtime in the school. Not related to this but based on your description, I can tell you that my overall network stability and useability increased dramatically when I started using the same SSID throughout the building and followed Cisco's recommendation of only using channels 1,6,and 11, spread out as much as possible, but some overlap is inevitable. If AP's are on the same channel and can see each other, they cooperate and minimize the interference. Wireless traffic on adjacent channels is seen by APs as wireless interference, or noise, and it slows the throughput.

I've recently experimented with some Open-Mesh wireless equipment, and that all uses the same channel, no matter how close together the APs are, and it all works very well. So I'd stick with the three channels. If you're in a '13 channel' part of the world, I believe you can use 4 successfully without interference (1,5, 9, 13?), but we have just 1,6, and 11 here. This latest version I got, which is older than the one that came with your new devices, was just released in May. The download page is: Don't worry about the overlap, just map out your areas of heaviest expect use, and try to arrange the nearest 3 APs to be on the three different channels.

In areas of lower use, I'd bet you could have five or more APs in the same room on the same channel, and you could use a couple laptops with no problem, only with a lot of devices would the bandwidth get streessed. The protocol for sharing wireless spectrum is pretty efficient. You might also consider putting one or more on the 5 Ghz band in heavy coverage/use areas. Most devices can use 5 Ghz in either 802.11n and or 802.11a nowadays. Still use same SSID though. It works great. Acer Synaptics Touchpad Driver Windows 10.

Lots of channels to choose from. Hi, We've got about 12 HP V-M200 APs in our furniture, the problem is that they require almost daily power cycles to continue functioning. They function correctly for a day or two, and then suddenly stop forwarding traffic. The SSID is still visible, and clients maintain their associations, but all network resources are inaccessible.

Some of these access points are being powered by POE and others are not. The same problem exists regardless. Also, they all have different SSID's and all APs within the same building are operating on different channels. They obtain IP's through DHCP reservations tied to their wireless MAC addresses. The current firmware is 5.4.1.0-01-9867 which came preinstalled.